PRODUCTS
UKS Water Set - Full Elastic Water Insulation Materials
 |  |
It is the full elastic, two-part, waterproofing and easy to use cement and acrylic based waterproofing material.
Product Description
It is the full elastic, two-part, waterproofing and easy to use cement and acrylic based waterproofing material.
Usage Areas
It is used in wet areas such as water tanks, gullies, waste water channels and piping, sealing pits, shear walls, basic basements, groundworks, bridges, thermal springs and public baths, kitchen, balcony, terrace, bathroom, wc, swimming and decorative pools..
Advantages of Product
It is full elastic, used indoors and outdoors, easy to prepare and apply (it can be applied by brush or trowel) , and its labor costs are low. Its processing time is long, it can be applied safely on horizontal and vertical surfaces, it is water based, solvent free, not toxic, can be used in water tanks, water or frost-resistant after curing, resistant to shock and vibration and it shows high adhesion and elasticity.
TECHNICAL DATA
Package 30 kg set (A: liquid 10 kgs; B: Powder 20 kgs)
Colour Grey, Green
Surface Temperature +5 °C / +30 °C
Pot Life 1 Hour (22 °C)
Mechanical Strength 2 days
Coating on 3 days
Wastage For single floor - 2,0 kgs / m2
Storage Shelf life - 12 months. Products should be stacked in a cool and dry place.
Surface Preparation and Preparation Instructions
The application floor should be cleared of loose fragments, oil and other chemicals and surface defects are repaired with the UKS Repair Concrete grout. If the substrate temperature is above 25 °C the surface is saturated dampening. UKS Latex should be used as an engobe on the surface. Pouring A: liquid component into a clean application container, pouring the whole B: Powder component, the component is blend with a suitable low-speed mixer for 3-4 minutes until all of the soil melts away and the homogeneous mixture is provided. Mixture is mixed again after being rested for 3-5 minutes and get ready for use. (Depending on air temperature 10% water can be added into mixture.) Application can be made by a brush or a trowel.
Application and Considerations
It is recommended to apply the first coat finely with brush adding 10% water into mixture. The thickness of each layer should not exceed 2 mm.
 It must be waited for 2-6 hours of drying time between each coat (depending on ambient conditions). In plaster mess applications; plaster mess is placed on the surface whilst the firs coat seems wet-dry and second coat is applied by a brush or trowel. Surface temperature must be minimum +5 °C. Applications must be protected from rain, frost, wind, sunlight and high heat for the first 24 hours. Hardening concrete grout must be diluted again.
It is the full elastic, two-part, waterproofing and easy to use cement and acrylic based waterproofing material.
Usage Areas
It is used in wet areas such as water tanks, gullies, waste water channels and piping, sealing pits, shear walls, basic basements, groundworks, bridges, thermal springs and public baths, kitchen, balcony, terrace, bathroom, wc, swimming and decorative pools..
Advantages of Product
It is full elastic, used indoors and outdoors, easy to prepare and apply (it can be applied by brush or trowel) , and its labor costs are low. Its processing time is long, it can be applied safely on horizontal and vertical surfaces, it is water based, solvent free, not toxic, can be used in water tanks, water or frost-resistant after curing, resistant to shock and vibration and it shows high adhesion and elasticity.
TECHNICAL DATA
Package 30 kg set (A: liquid 10 kgs; B: Powder 20 kgs)
Colour Grey, Green
Surface Temperature +5 °C / +30 °C
Pot Life 1 Hour (22 °C)
Mechanical Strength 2 days
Coating on 3 days
Wastage For single floor - 2,0 kgs / m2
Storage Shelf life - 12 months. Products should be stacked in a cool and dry place.
Surface Preparation and Preparation Instructions
The application floor should be cleared of loose fragments, oil and other chemicals and surface defects are repaired with the UKS Repair Concrete grout. If the substrate temperature is above 25 °C the surface is saturated dampening. UKS Latex should be used as an engobe on the surface. Pouring A: liquid component into a clean application container, pouring the whole B: Powder component, the component is blend with a suitable low-speed mixer for 3-4 minutes until all of the soil melts away and the homogeneous mixture is provided. Mixture is mixed again after being rested for 3-5 minutes and get ready for use. (Depending on air temperature 10% water can be added into mixture.) Application can be made by a brush or a trowel.
Application and Considerations
It is recommended to apply the first coat finely with brush adding 10% water into mixture. The thickness of each layer should not exceed 2 mm.
 It must be waited for 2-6 hours of drying time between each coat (depending on ambient conditions). In plaster mess applications; plaster mess is placed on the surface whilst the firs coat seems wet-dry and second coat is applied by a brush or trowel. Surface temperature must be minimum +5 °C. Applications must be protected from rain, frost, wind, sunlight and high heat for the first 24 hours. Hardening concrete grout must be diluted again.